Waste Incinerators - HICLOVER Incinerator

The cost of a small incinerator

Posted on August 17, 2021 by admin

Medical Waste Incinerator Capacity: Typical 50-100 kgs Each hour

Items/Model

TS50(PLC)

Picture

Principle

Medical Waste Incineration

Burn Rate

Average 50-100 kg/hour

Feed Capacity

Average 100kg/feeding

Control Mode

PLC(Programmable Logic Controller Incinerator)

Combustion Chamber

560L

Internal Dimensions

100x80x70cm

Secondary Chamber

280L

Smoke Filter Chamber

Yes

Feed Mode

Manual

Voltage

220V

Power

0.7Kw

Oil Infection (kg/hour)

Typical 16.9

Gas Consumption (m3/hour)

Typical 20.2

Infection Monitor

Digital Screen

Temperature Protection

Yes

Oil Tank

100L

Feed Door

70x55cm

Chimney

5Meter

Chimney Type

Stainless Steel

1st.

Gross Weight

4500kg

External Dimensions

230x130x155cm

Optional Part: Stainless Steel Wet scrubber

HICLOVER Incinerator/Parts Range

Main Feature

Medical Waste Incinerators

Phone: +86-13813931455(whatsapp/wechat)
Website: http://www.hiclover.com/

HICLOVER 10-500kgs/Hr.Double Combustion Chambers

Email: [email protected]
Email: [email protected]

Nanjing Clover Medical Technology Co.,Ltd.

Single Combustion Chamber	Small, Cheap,10-20kgs/Hr.
Three Combustion Chambers(Optional)	3 Chambers for high risk waste
Pet Cremation Equipment	For Pet(small/big) Cremation Business
Animal Incineration Equipment	For other creature incineration
	Items/Model
TS100(PLC)	TS150(PLC)

TS300(PLC)

TS500(PLC)	Burn Speed (Average)	100 kg/hour	150 kg/hour	300 kg/hour
500 kg/hour	Control Mode	PLC Auto.	PLC Auto.	PLC Auto.
PLC Auto.	Combustion Chamber	1200L	1500L	2000L
3000L	Internal Dimensions	120x100x100cm	150x100x100cm	170x120x100cm
210x120x120cm	Secondary Chamber	600L	750L	1000L
1500L	Smoke Filter Chamber	Dry Scrubber	Dry Scrubber	Dry Scrubber
Dry Scrubber	Feed Mode	Manual	Manual	Manual
Manual	Voltage	220V	220V	220V
220V	Power	1.38Kw	1.69Kw	2.57Kw
4.88Kw	Diesel Oil Consumption (kg/hour)	Ave.20.4	Ave.24.2	Ave.33
Ave.44	Natural Gas Consumption (m3n/hour)	Ave.24.5	Ave.29	Ave.39.6
Ave.52.8	Infection Monitor	Yes	Yes	Yes
Yes	Temperature Protection	Yes	Yes	Yes
Yes	Oil Tank	200L	300L	500L
500L	Chimney	10Meter	10Meter	14Meter
14Meter	Chimney Type	Stainless Steel	Stainless Steel	Stainless Steel
Stainless Steel	1st. Chamber Temperature	800℃–1000℃	800℃–1000℃	800℃–1000℃
800℃–1000℃	2nd. Chamber Temperature	1000℃-1200℃	1000℃-1200℃	1000℃-1200℃
1000℃-1200℃	Residency Time	2.0 Sec.	2.0 Sec.	2.0 Sec.
2.0 Sec.	Gross Weight	6000kg	8500kg	11000kg
16000kg	External Dimensions	260x150x180cm	300x160x190cm	400x210x300cm
450x210x300cm

Sudan Kassala state and we are working on installing an incinerator for Girba hospital in Girba locality.

CE Certification Pass

HICLOVER Solution for Fighting COVID-19 with CE Certification.

1. Medical Waste Incinerator(Containerized Mobile Incinerator｜Top Loading Incinerator)

2. Auto Roll Air Filter for Clean Room

2020-10-28

Medical Incinerator Specification

Posted on August 17, 2021 by admin

Capacity Not less than 500Kg/hr.
Operation 24hr-7days/week continuous operation.
Combustion chamber 2 combustion chamber.
Temp. First combustion chamber 800-1000 C.
Secandry combustion chamber 1000-1200 C, with the possibility to be upgraded to 1400 C.
Combustion Efficiency 99.99%
Retention time Of the flow gases not less than 2 Sec in the hot portion.
Excess Oxygen concentration Of primary combustion chamber 3-6% max.

Refractory The chambers should be lined with high thermal insulating refractory bricks with suitable thickness and with highly temp.
resistance. Not less than 1400 C for the first combustion chamber, and not less than 1600 C for the secandry combustion chamber, and at the
same time prevent the Temp. of the outside body of the chamber not higher than 70 C.
Doors Should be lined with the same bricks, and the edges lined with special suitable insulating material to prevent any gas escaping, and
the doors should be kept under negative pressure during the operation.
Air Emission Control System With high destruction and removal efficiency (DRE). Not less than 99.9999 as per KEPA.
Wet System If the system equiped with a CEMS washing the flow gas with water, then it should be manufactured from suitable anti
corrossion materials, and equiped with pH meter to measure and neutralize the water. It should be able to use the water in closed recycled
circuit many times before treating/ discharging into the sewage system in compliance with KEPARS.
Chemical dosing It should be equiped with suitable autochemical dosing system to control the pH for the water of the wet scrubber system
including sensors.
Chimney It should be suitable with the capacity and the technical specifications, with height not less than 12m from ground level. With easy
opennable sampling point equal about 3 inch, and the optimum sampling locations is at least 8D downstream direction and 2D upstream from any
flow disturbancies.
Sampling point Should be equiped with a platform located down the sampling point by a distance not less than 1 m, and equiped with suitable
stairs from ground to the port with comfortable slope.
Ash Removal It should be auto ash removal system.
Fuel It should be dual system, such as diesel and natural gas.
Feeding System Should be auto feeding system into primary chamber.
Control Room Should be equiped with a control panel shows Temp. of the combustion burners, gas monitoring, digital Temp. indecation for the
primary/secondary chambers, digital Temp. indication for the gases…etc. it should be also Auto operation, burnures on/off auto lamps switch,
auto start/stop for air emission control system, auto gas continuous monitoring system reading and print out of gas emission parameters…etc.
Cooling System The primary chamber should be provided with auto cooling systemthrough nozzles to permit direct cooling if the Temp. will be
heigher than 1100 C.
Inter-lock system The incinerator should be equiped with inter-lock system to prevent feeding the waste to the primary chamber if the
combustion Temp. less than 500 C.
Flue treatment and cleaning To consist a combined system (wet/dry), using water, lime, active carbon and ceramic filters.
Quenching system/Heat exchanger Should be made and manufactured from anti corrosion and acid attack materials such as stainless steel 316 or
equivalent.
Noise Level Not more than 85 dBA during normal operation.
Inaddition The desigh should insure that responsive fail-safe control systems are used.
The incinerator should be installed inside closed suitable building with good aeration and ventilation system. The building has
facilities for off-loading of wastes from transport vehicles. Auto cleaning system for trucks and waste containers, and cool storage
area…etc.
The quotation should included list of original spare parts for 7 years.
The quotation should include supervising, starting up and training of the operators and ministry of health engineers inside/outside
Kuwait.
Detailed drawings, catalogs should be included.

Medical Waste Incinerator

Posted on August 16, 2021 by admin

Phone: +86-13813931455(whatsapp/wechat)
Website: http://www.hiclover.com/

Email: [email protected]
Email: [email protected]

Nanjing Clover Medical Technology Co.,Ltd.

Three Combustion Chambers(Optional)	3 Ranked for high risk waste
Pet Cremation Equipment	For Pet(small/big) Cremation Business
Animal Incineration Equipment	For other creature incineration
	Items/Model
TS100(PLC)	TS150(PLC)
TS300(PLC)	TS500(PLC)

Burn Speed (Typical )

100 kg/hour	150 kg/hour	300 kg/hour	500 kg/hour	Control Mode
PLC Auto.	PLC Auto.	PLC Auto.	PLC Auto.	Combustion Chamber
1200L	1500L	2000L	3000L	Internal Dimensions
120x100x100cm	150x100x100cm	170x120x100cm	210x120x120cm	Secondary Chamber
600L	750L	1000L	1500L	Smoke Filter Chamber
Dry Scrubber	Dry Scrubber	Dry Scrubber	Dry Scrubber	Feed Mode
Manual	Manual	Manual	Manual	Voltage
220V	220V	220V	220V	Power
1.38Kw	1.69Kw	2.57Kw	4.88Kw	Diesel Oil Consumption (kg/hour)
Ave.20.4	Ave.24.2	Ave.33	Ave.44	Natural Gas Consumption (m3n/hour)
Ave.24.5	Ave.29	Ave.39.6	Ave.52.8	Infection Monitor
Yes	Yes	Yes	Yes	Temperature Protection
Yes	Yes	Yes	Yes	Oil Tank
200L	300L	500L	500L	Chimney
10Meter	10Meter	14Meter	14Meter	Chimney Type
Stainless Steel	Stainless Steel	Stainless Steel	Stainless Steel	1st. Chamber Temperature
800℃–1000℃	800℃–1000℃	800℃–1000℃	800℃–1000℃	2nd. Chamber Temperature
1000℃-1200℃	1000℃-1200℃	1000℃-1200℃	1000℃-1200℃	Residency Time
2.0 Sec.	2.0 Sec.	2.0 Sec.	2.0 Sec.	Gross Weight
6000kg	8500kg	11000kg	16000kg	External Dimensions
260x150x180cm	300x160x190cm	400x210x300cm	450x210x300cm
			Three Combustion Chambers(Optional)	3 Ranked for high risk waste

www.hiclover.com

********************************************************************************************************

HICLOVER Solution for Fighting COVID-19, with CE Certification Pass.

1. Medical Waste Incinerator(Containerized Mobile Incinerator｜Top Loading Incinerator)

2. Auto Roll Air Filter for Clean Room

Pet Cremation Equipment

2020-10-28

Medical Environmental ｜Waste Incinerators ｜Auto Roll Air Filters

Medical Waste Incinerator ｜Mobile Incinerator｜

Pet Animal Incinerator｜Municipal Solid Waste Incinerator

For Pet(small/big) Cremation Business

Online Contact Form/Subscribe to Newsletter: http://www.hiclover.com/contact/

Power

kW

Mcal/h 178 – 356

153 – 306

Fuel consumption rate L/h 15 – 30

Fuel Domestic fuel oil

Internal calorific value kWh/kg

Mcal 11.8

10.2 (10,200 kcal/Kg)

Density kg/dm3 0.82 C 0.85

Viscosity at 20°C mm2/s max 6

Operation Intermittent (1 min stop in 24 h)

One speed (on or off)

Sprinkler Number 1

Standard use Water, steam, diathermic oil boiler

Ambient temperature °C 0 C 40

Combustion Air Temperature °C max 60

Combustion temperature °C 900 to 1100

Destructive capacity Kg/h (l/h) 120 (1600)

Power supply V

Hz 230 +/- 10%

50 single-phase

Electric motor rpm

W

V

A 2800

0.25

230

2.1

Motor capacitor µF/V 8/450

Ignition transformer V1 – V2

I1 – I2 230V – 8kV

1.8A – 30mA

flow 12 bans

Pump – pressure range

temperature

kg/h

bar

°C max 65

10 C 18

60

Degree of protection IP 40

Power consumption w max 0.43

Chimney height m 6 to 8

Chimney diameter mm Approximately 500

Tank volume l 1000 to 1200

Number of ovens 2 to 3

Dimensions of the loading door cm About L80 x B60

Combustion chamber: One-piece casing made of 3- and 10-mm thick sheet steel. Loading front with sealed door mounted on hinges, screw-type closing wheel, flexible seal, and refractory insulating lining.

Chamber materials made of refractory concrete with an alumina content of 42%AL2O3 and a wall thickness of 115 mm. Equipped with thermal insulation in fibrous panels made of calcium silicate with a thickness of 75 mm. It must also be equipped with a waste ignition burner.

Post-combustion chamber A post-combustion chamber for gases meeting the emission standards for certain gases (CO, HCl, SO2, NOx, etc.).

Filter Allowing combustion control and regulation of the treatment process;

A filter for reducing air pollution from incineration

Metal scraper A metal scraper and an ash pan with handling handle.

Paint: light blue

Animal Incineration Equipment

For other creature incineration

New medical waste incinerator for Afghanistan and Macau in October,2014

Posted on August 15, 2021 by admin

Medical Incinerator Specification

Posted on August 14, 2021 by admin

Capacity Not less than 500Kg/hr.
Operation 24hr-7days/week continuous operation.
Combustion chamber 2 combustion chamber.
Temp. First combustion chamber 800-1000 C.
Secandry combustion chamber 1000-1200 C, with the possibility to be upgraded to 1400 C.
Combustion Efficiency 99.99%
Retention time Of the flow gases not less than 2 Sec in the hot portion.
Excess Oxygen concentration Of primary combustion chamber 3-6% max.

Refractory The chambers should be lined with high thermal insulating refractory bricks with suitable thickness and with highly temp.
resistance. Not less than 1400 C for the first combustion chamber, and not less than 1600 C for the secandry combustion chamber, and at the
same time prevent the Temp. of the outside body of the chamber not higher than 70 C.
Doors Should be lined with the same bricks, and the edges lined with special suitable insulating material to prevent any gas escaping, and
the doors should be kept under negative pressure during the operation.
Air Emission Control System With high destruction and removal efficiency (DRE). Not less than 99.9999 as per KEPA.
Wet System If the system equiped with a CEMS washing the flow gas with water, then it should be manufactured from suitable anti
corrossion materials, and equiped with pH meter to measure and neutralize the water. It should be able to use the water in closed recycled
circuit many times before treating/ discharging into the sewage system in compliance with KEPARS.
Chemical dosing It should be equiped with suitable autochemical dosing system to control the pH for the water of the wet scrubber system
including sensors.
Chimney It should be suitable with the capacity and the technical specifications, with height not less than 12m from ground level. With easy
opennable sampling point equal about 3 inch, and the optimum sampling locations is at least 8D downstream direction and 2D upstream from any
flow disturbancies.
Sampling point Should be equiped with a platform located down the sampling point by a distance not less than 1 m, and equiped with suitable
stairs from ground to the port with comfortable slope.
Ash Removal It should be auto ash removal system.
Fuel It should be dual system, such as diesel and natural gas.
Feeding System Should be auto feeding system into primary chamber.
Control Room Should be equiped with a control panel shows Temp. of the combustion burners, gas monitoring, digital Temp. indecation for the
primary/secondary chambers, digital Temp. indication for the gases…etc. it should be also Auto operation, burnures on/off auto lamps switch,
auto start/stop for air emission control system, auto gas continuous monitoring system reading and print out of gas emission parameters…etc.
Cooling System The primary chamber should be provided with auto cooling systemthrough nozzles to permit direct cooling if the Temp. will be
heigher than 1100 C.
Inter-lock system The incinerator should be equiped with inter-lock system to prevent feeding the waste to the primary chamber if the
combustion Temp. less than 500 C.
Flue treatment and cleaning To consist a combined system (wet/dry), using water, lime, active carbon and ceramic filters.
Quenching system/Heat exchanger Should be made and manufactured from anti corrosion and acid attack materials such as stainless steel 316 or
equivalent.
Noise Level Not more than 85 dBA during normal operation.
Inaddition The desigh should insure that responsive fail-safe control systems are used.
The incinerator should be installed inside closed suitable building with good aeration and ventilation system. The building has
facilities for off-loading of wastes from transport vehicles. Auto cleaning system for trucks and waste containers, and cool storage
area…etc.
The quotation should included list of original spare parts for 7 years.
The quotation should include supervising, starting up and training of the operators and ministry of health engineers inside/outside
Kuwait.
Detailed drawings, catalogs should be included.

HICLOVER TS Model Incinerator

Posted on August 14, 2021 by admin

Phone: +86-13813931455(whatsapp/wechat)
Website: http://www.hiclover.com/

Email: [email protected]
Email: [email protected]

Nanjing Clover Medical Technology Co.,Ltd.

	HICLOVER Incinerator/Parts Range
Main Feature	Medical Waste Incinerators
HICLOVER 10-500kgs/Hr.Double Combustion Chambers	Single Combustion Chamber
Small, Cheap,10-20kgs/Hr.	Three Combustion Chambers(Optional)
3 Ranked for high risk waste	Pet Cremation Equipment
For Pet(small/big) Cremation Business	Animal Incineration Equipment

For additional creature incineration

	Items/Model	TS100(PLC)	TS150(PLC)	TS300(PLC)
TS500(PLC)	Burn Rate (Typical )	100 kg/hour	150 kg/hour	300 kg/hour
500 kg/hour	Control Mode	PLC Auto.	PLC Auto.	PLC Auto.
Combustion Chamber	1200L	1500L	2000L	3000L
Internal Dimensions	120x100x100cm	150x100x100cm	170x120x100cm	210x120x120cm
Secondary Chamber	600L	750L	1000L	1500L
Smoke Filter Chamber	Dry Scrubber	Dry Scrubber	Dry Scrubber	Dry Scrubber
Feed Mode	Manual	Manual	Manual	Manual
Voltage	220V	220V	220V	220V
Power	1.38Kw	1.69Kw	2.57Kw	4.88Kw
Diesel Oil Consumption (kg/hour)	Ave.20.4	Ave.24.2	Ave.33	Ave.44
Natural Gas Consumption (m3n/hour)	Ave.24.5	Ave.29	Ave.39.6	Ave.52.8
Infection Monitor	Yes	Yes	Yes	Yes
Temperature Protection	Yes	Yes	Yes	Yes
Oil Tank	200L	300L	500L	500L
Chimney	10Meter	10Meter	14Meter	14Meter
Chimney Type	Stainless Steel	Stainless Steel	Stainless Steel	Stainless Steel
1st. Chamber Temperature	800℃–1000℃	800℃–1000℃	800℃–1000℃	800℃–1000℃
2nd. Chamber Temperature	1000℃-1200℃	1000℃-1200℃	1000℃-1200℃	1000℃-1200℃
Residency Time	2.0 Sec.	2.0 Sec.	2.0 Sec.	2.0 Sec.
Gross Weight	6000kg	8500kg	11000kg	16000kg
External Dimensions	260x150x180cm	300x160x190cm	400x210x300cm	450x210x300cm

UNAMID supports its dependants via the operation of several self-sustained camps located across the mission AOR. These camps contain all elements representative of small communities. These communities include hospitals and medical facilities, power generation stations, grocery shops, kitchen and dining facilities and large scale use of packaged material in plastic, cardboard and similar. The waste generated in these camps are therefore representative of average small communities without heavy industry. The main objective of this document is to provide potential bidders with necessary information to supply the large capacity containerized incinerators to UNA M I D as described in subsequent clauses.

1. Medical waste incinerator – Small

2. Medical waste incinerator – Medium

3. General waste incinerator – Small

4. General waste incinerator – Medium

5. General waste incinerator – Large

5. General waste incinerator – Large with automated feeding system

Supply of Medical and General waste incinerators

FOR THE PROVISION OF

LARGE CAPACITY CONTAINERIZED INCINERATOR AND ACCESSORIES

The proposed incinerators shall be built into standard 20ft lSO contai ners or alternatively built into similar footprint complete with ISO load handling facil ities (hooks噜 eyelets, etc). The number of conta iners/container sized modules required for each unit is at the discretion of the Contractor.

•Thermocouple

•temperature gauge

•fire rope

•burn er

•induction air fan

•digital temperature display panel

The incinerator combustion chamber(s) should be designed for easy maintenance of all internal parts including the refractory and insulation. Materials used in the individual parts of the incinerator shall be heat resistance and also be protected against oxidation, corrosion , etc. The incinerator shell shall be made of mild steel with an adequate thickness (minimum 15 mm) and painted externally with heat resistant aluminium paint suitable to withstand 250 °C. The outside surface temperature of the incinerator casing should not exceed 50 °C above ambient temperature and shall include a safety mesh around all hot surfaces. Cold face refractory lining of calcium silicate or superior material, minimum thickness 100mm.

•Heavy steel construction.

•Fixed hearth geometry and starved air gasification operationa l mode.

•Hot face refractory concrete-ceramic suitable for thermal shock up to 1400 Celsius and abrasion. Minimum thickness 150mm.

•Cold face refractory lining of calciu m si l icate or superior material, minimum thickness 100mm.

•Refractory lining of all the ducts shall be done with refractory castings. Su perior quality ceramic wool shall be used at all hot duct flanges and expansion j oints.

•Multi ple electric ignition fuel bu rners designed to use automotive d iesel fuel.

•Flame of the primary burner shall be oriented towards the center of the uni t which does not impinge directly on the refractory floor or wall. The secondary burner shall be positioned in such a way that the flue gas passes through the flame.

•The unit shal l prevent leakage of the hot flue gas and any backfire.

HICLOVER Solution for Fighting COVID-19, Medical Waste Incinerator

2020-09-17

Now you can move your incinerator by truck to anywhere! Containerized waste incinerator is our latest design for market. This incinerator is build in ISO

Posted on August 13, 2021 by admin

Best Feeding Door HICLOVER 10-500kgs/Hr.Double Combustion Chambers Waste Incinerators

Posted on August 12, 2021 by admin

Phone: +86-13813931455(whatsapp/wechat)
Website: http://www.hiclover.com/

Email: [email protected]
Email: [email protected]

Nanjing Clover Medical Technology Co.,Ltd.

HICLOVER is currently offering a broad selection of medical waste incinerators, designed to provide efficient waste destruction, using best available technologies and environmentally friendly procedure. Due to the secondary room with its 2 minute retention period, our healthcare incinerator range is well suited to process clinical waste.

Our products guarantee effective, clean and hassle-free disposal of medical waste is possible. The incineration of clinical waste such as pathological waste (red bag waste), Biohazards & Sharps, General Medical Waste, from Hospitals, Research Center, Pharmaceutical Companies, Medication Manufactures, Primary Care Trusts, Cosmetic Surgery Clinics, Nursing Homes, Care Homes and other Clinical Waste.

Items/Model	TS100(PLC)	TS150(PLC)	TS300(PLC)	TS500(PLC)
Burn Rate (Average)	100 kg/hour	150 kg/hour	300 kg/hour	500 kg/hour
Control Mode	PLC Auto.	PLC Auto.	PLC Auto.	PLC Auto.
Combustion Chamber	1200L	1500L	2000L	3000L
Internal Dimensions	120x100x100cm	150x100x100cm	170x120x100cm	210x120x120cm
Secondary Chamber	600L	750L	1000L	1500L
Smoke Filter Chamber	Dry Scrubber	Dry Scrubber	Dry Scrubber	Dry Scrubber
Feed Mode	Manual	Manual	Manual	Manual
Voltage	220V	220V	220V	220V
Electricity	1.38Kw	1.69Kw	2.57Kw	4.88Kw
Diesel Oil Consumption (kg/hour)	Ave.20.4	Ave.24.2	Ave.33	Ave.44
Natural Gas Consumption (m3n/hour)	Ave.24.5	Ave.29	Ave.39.6	Ave.52.8
Infection Monitor	Yes	Yes	Yes	Yes
Temperature Protection	Yes	Yes	Yes	Yes
Oil Tank	200L	300L	500L	500L
Feed Door	80x60cm	80x60cm
Chimney	10Meter	10Meter	14Meter	14Meter
Chimney Form	Stainless Steel	Stainless Steel	Stainless Steel	Stainless Steel
1st. Chamber Temperature	800℃–1000℃	800℃–1000℃	800℃–1000℃	800℃–1000℃
2nd. Chamber Temperature	1000℃-1200℃	1000℃-1200℃	1000℃-1200℃	1000℃-1200℃
Residency Time	2.0 Sec.	2.0 Sec.	2.0 Sec.	2.0 Sec.
Gross Weight	6000kg	8500kg	11000kg	16000kg
External Dimensions	260x150x180cm	300x160x190cm	400x210x300cm	450x210x300cm

Type of waste: medical and industrial (solid and semi solid hazardous)

Type of waste : Bio-medical & Hazardous (Solid and Semi Solid)

If you are a hospital then Please also tell how many bedded hospital : No aren’t a hospital

Quantity of waste generated per day in kg : 6000 kg

Duration C incinerator will be used per day :1 C 16 hours

Approximate moisture content: 47 to 53%

Availability of power and type : 3 Phase, 440 Volts

Details of space available : Min. 10000 Sq. ft.

Do you require an automatic loading system? Depends if it is a continuous burning or interval burning.

How soon do you require the system to be delivered? 8 weeks

Whether the location is a coastal area : No

An other specific requirements: Automatic PLC Control System.

Burning Rate: 500kg/hour

Volumetric capacity Primary Chamber: 500kg

Burner Type: Diesel Operated

Burning Process: Continuous

HICLOVER Solution for Fighting COVID-19, Medical Waste Incinerator

2020-09-16

Actually, from year 2013, we will pay insurance fee under each contact and customer do not need to pay this cost. Under the term FOB/C&F/CIF,

Posted on August 11, 2021 by admin

Medical Incineraotors chamber of post combustion

Posted on August 10, 2021 by admin

1.A chamber of post combustion of gases
A burner of combustion of gases,
A device of injection of air allowing a total re-combustion of gases,
A device of air inlet of cooling of waste gases,
A sheath of evacuation of the gases burnt,
Carcass in strong sheet steel with support of connection
Composition of the refractory;
Refractory concrete:
Thickness :>150mm
Nature: 65%% of Al203
Insulate in fibrous panels:
Thickness: >85mm
Nature: Calcium
Burner with fuel, mono-bloc casting guiding type with horizontal flame, lighting and safety of electronic ignition, permanent ventilation,
electromagnetic sluice gate of regulation and isolating valve.
A secondary injection of air to ensure perfect oxygen content.
2.A control box ensuring the complete cycle of combustion.
3.Fan:
Electro-ventilator distributing the secondary air, the regulation of the air flow being carried out by valves and following the control of
the automatic cycle.
4.Controls and regulations:
Control box watertight to dust, including:
A switch circuit breaker for each engine (ventilators and burners).
A timer with adjustable temporization for the regulation of each burner.
A regulator with digital watching for the temperature of combustion.
A regulator with digital watching for the temperature of post-combustion.
Electric box.
5.The de-ashing must be done in the bottom of the combustion chamber or the de-ashing should be automatic or manual batch de-ashing.
6.Process filtering system: scrubber to be mentioned as optional
7.Emission standards compliance: BS 3316 or equivalent standard
8.Capacity to treat plastic: not less than 40% by weight
9.CE manufacturing compliance: BS EN 746-2-1997

Medical Waste Incinerator Capacity: Typical 50-100 kgs Each hour	Items/Model
TS50(PLC)	Picture
	Principle
Medical Waste Incineration	Burn Rate
Average 50-100 kg/hour	Feed Capacity
Average 100kg/feeding	Control Mode
PLC(Programmable Logic Controller Incinerator)	Combustion Chamber
560L	Internal Dimensions
100x80x70cm	Secondary Chamber
280L	Smoke Filter Chamber
Yes	Feed Mode
Manual	Voltage
220V	Power
0.7Kw	Oil Infection (kg/hour)
Typical 16.9	Gas Consumption (m3/hour)
Typical 20.2	Infection Monitor
Digital Screen	Temperature Protection
Yes	Oil Tank
100L	Feed Door
70x55cm	Chimney
5Meter	Chimney Type
Stainless Steel	1st.
Gross Weight	4500kg
External Dimensions	230x130x155cm
	Optional Part: Stainless Steel Wet scrubber
	HICLOVER Incinerator/Parts Range